CR-10 Base Enclosure with Storage Drawer

Categories
Builds

Creality CR-10 Riser Kit

The CR-10 is an amazing printer. However, it does take up quite a bit of precious area in my small workshop so I decided to build a thin case under it. The computer is in the rear part of of the case, and the front will have drawers for storage.

The Materials

  • 1/4 MDF
  • M4 screws
  • CR-10 3d Printer
  • Wood glue

The Tools

  • CO2 laser cutter

The Build

Original CR-10

Here is the original CR-10. There’s that big ugly box on the side of it. It’s so tall that another couple inches isn’t going to matter.

I took apart my CR-10 to examine all the wires, components, etc so I could get a good idea of where to place everything.

Here are the internals of the printer. Pretty basic stuff actually. The power supply is the biggest thing. The board for controlling stuff, the mosfet for handling high current to the heating bed, a couple fans. I also added a raspberry Pi to run OctoPrint.

The drawer with pull cutout

Based on previous projects, I am not going to leave any tolerance for the drawer. I put 1-2mm before and there was a huge gap, so going to gamble with a perfect fit here.

Finished cutting, everything but the top assembled

I glued the drawer together to prevent any screws sticking out messing with the clearance. The main case however is bolted together with M3 hardware. Getting ready to mount the components in! I decided to add a 1mm clearance to the drawers, I think that’s the right amount for all projects going forward. I did a quick test with 0 and it was just too tight.

Internals installed, what a mess

I used double sided tape to mount the power supply, Raspberry, and other stuff. Surprisingly all the hole cutouts I measured pretty accurately! Maybe I’m finally getting better at this.

Final product with printer running

Put everything back together, removed the printer rubber legs and let the printer sit flush on the enclosure. Everything fits perfectly, the drawer works great. I left the top screws off just in case I need to get back into the internals. Gravity does a good enough job of keeping it in place.

Printer back in action

Back on line printing again. Steady helping to make masks/equipment for donation for this CoVid-19 thing.

Updates

I added a nice coat of matte black paint to match the printer. Normally I like to leave MDF unpainted, but wanted a more unified look for the printer.

Side view of the printer

I thought I did a pretty good job with the fan grill.

Picture of the drawer

I left the inside of the drawer unpainted to make it easier to see the stuff inside.

Final product busy printing masks

Rubiks Cube Pi Case Fusion 360

Categories
Builds

Raspberry Pi Rubik’s Cube Case

I have a 3TB RAID1 ext4 NAS and set up a Raspberry Pi 2 to serve as a streaming media center. I wanted to come up with a cool case. Since the dual drives + Pi is roughly square-ish, I came up with the idea to make a rubik’s cube case. Initially it was just going to be a solid block, but then I decided to make it actually rotate horizontally.

The Materials

  • 1/4 MDF panels
  • color card stock
  • Raspberry Pi / NAS hard drives, power cables
  • black matte spray paint
  • wood glue
  • spray adhesive

The Tools

  • CO2 laser cutter
  • wood glue
  • Fusion360
  • Lightburn

The Build

One side of the cube with the color panels

All the panels will be made of 1/4 MDF. If you look closely, you can see the perforations between the color panels that is meant to allow air flow.

First cut, surprisingly everything is working out perfectly

This is the most cutting I’ve ever done for a project. I used a full 2×4 and them some.

60 watts and 50-60% cutting light butter

I noticed that new/dry MDF cuts much better than old or boards with some condensation. Usually I would have to pop the pieces out, but this project, everything fell out perfectly.

I used card stock to color the panels

I used adhesive spray to add the colored card-stock to the panel pieces. I designed the panels to stick up to give the the colors texture.

The inside of the cube

The design uses a thin cut ring to allow the 3 levels to spin around. I just used wood glue to stick the thin ring to the 1st and 3rd levels, and the middle level circle is slightly larger. I didn’t leave any tolerance, but it was a tight fit and so far works perfectly.

Got impatient placed some of the panels on for a preview
Painted the interior with matte paint

The inside of a rubiks cube is black, so did a light spray of matte paint. Also works to hide the laser cut edges.

Final product, time to install the Raspberry and hard drives.

All that’s left is to install the hard drive and Pi. In retrospect, I made the cube a little too big. I could have spent the time to disassemble the SATA base/connectors. I might redo this to make it more compact.

Installed internals, up and running!

Here is its final resting place, next to my router, serving media. If i didn’t make it able to turn, I could have definitely made the case smaller.

Mistakes

  • built the inside too large, however, might make the most of it by adding motorized movement
  • used card stock instead of adhesive vinyl, which would look more like a rubik’s cube
  • the blue color i’m not a fan of, need a darker blue but we’re in a quarantine because of coronavirus

Updates

  • I got new cardstock and updated the blue color to match the classic cube, so much better!
  • Replaced the Pi 2 1GB with Pi 4 4GB… runs so much faster

Categories
Builds

Espresso Station

This is a little cubby drawer station I made to go with my Breville Barista Express machine. It is meant to store drink mixes, tea, espresso supplies, sugar, cups.

The Tools

  • 60 watt CO2 laser
  • rubber bands
  • Fusion360
  • Lightburn

The Materials

  • 5mm birch plywood
  • wood glue
  • sandpaper

The Build

The main body with mini handles for easy lifting, and a small wall around the edge

The empty space will have a drawer that slides in and out for main storage of tea bags, supplies, etc.

Draw with openings on both sides

I designed the drawer with a 2mm tolerance on all sides and found out that was way too much. I should have done 1mm or less. I put the hole handes on both sides to allow for air to escape because I assumed it would be a tight fit.

My trusty 60 watt CO2 laser

This is my first project with birch plywood. I did NOT know that the middle layers of the plywood were not 100% filled. Surprisingly, this 5mm birch cut much easier than 6.3mm MDF.

Rubber bands and wood glue

Putting together the pieces was messy. I used steel wool to brush off the ash from the laser cuts, but it still got everywhere.

Wood dried and cleaned

I tried to sand off the dirty ash, but found out that a damp cloth worked even better to clean up all the dirty ash from the surface.

Finished product

I engraved a little coffee logo on the front just for fun. In retrospect, the design is much too long, I could have made it a little more compact.

Mistakes

  • top-front piece was designed with no interlocking joint and relies entirely on glue
  • the 2mm gap tolerance for the drawer is way too much
  • tried to sand off ash instead of wiping it down
  • design too long, need to shorten it
  • found out i added tolerance to BOTH pieces, doubling up on the gap
  • need to engrage the logo a bit darker next time
  • need to round off the fillet on the handles more to match the drawer handle

Updates

Redid the design to make it shorter, also fixed the front top piece so that it interlocks properly. I also burned the espresso logo in the front darker and rounded off the fillets.

More reasonable looking
Categories
Builds

LEGO Minifig Display Case

I previously built a minifig display case but it was big, heavy, and awkward. It also did not have a glass cover in the front and seemed to collect lots of dust, so I decided to redo it.

The Tools

  • Fusion 360 / Lightburn
  • 60 watt CO2 laser
  • staple gun
  • drill (only for pilot holes)

The Materials

  • 1/4 inch MDF
  • 5x3mm circular neodymium magnets
  • plexiglass
  • support board
  • sawtooth picture frame mounts
  • epoxy
  • hot glue gun

The Build

Shelves with engraved placement markings

I decided to make it 5 columns 4 rows of minifigs so 20 per display case. The Fusion360 design is totally parametric (I think) so I can easily adjust these to customize it.

Case put together

There are 3 types of material used. 1/4 MDF for the frame and shelves, the white support board (like you get from cheap bookshelves), and plexiglass for the front cover.

M3 nuts and bolts to hold the frame together

I used bolts for the 4 corners of the frame. I did not want to use glue. Here you can see the notch that holds the M3 bolts.

Glass with magnets holding the cover

I used neodymium magnets, 5x3mm circles, to hold the front glass together. The 1st and 3rd shelves have notches where I used epoxy to glue 4 magnets to the shelf. There are also 3mm holes cut in the plexiglass. It’s kind of weird, but works and I didn’t have to use any hinges.

Added the minifigs

I used a hot glue gun to mount the minifigs using the engraged indicators for perfect spacing!

Small collection of figures

After the first one was a success, I made 2 more. Still need another one!

Mounted using picture frame hangers

I used 2 sawtooth picture frame mounts per display case to mount everything to the wall. All done!

Mistakes

  • probably could have designed the frame mounts in the other direction so the frame can sit flush on a flat surface

Updates

I created another size for my 4 larger minifigs. It really tested my parametric design, which didn’t do so well so I had to make updates.

2×2 custom frame

I noticed that my MDF was pretty fresh, so it was dry and also not as thick as I spec’d it out for. Also, I put the magnets in the middle, but since there is only 1 shelf, it’s a little wobbly. Going to add stoppers the top and bottom to make sure the glass sits straight.

Categories
Builds In Progress

CO2 Laser Control Panel

I absolutely LOVE my Class 4 CO2 Laser cutter/engraver. But it definitely needs some improvements. I’ve added custom lighting, camera, and analog milliamp reader to it and needed a control panel to manage everything. I designed this as an inset panel that controls the AC lines (which are connected to a new UPS).

Prototype test plate

My 3d printer always prints a little larger. My designs need about 0.5-1mm tolerance for fittings so I printed out this flat plate to test the panel mounted switches and hole placements.

Categories
Builds

Picture Frame

Emma made me this beautiful ceramic heart for Valentines Day! I decided to make a lightbox style frame to hang it on the wall using slots and glue to keep everything secure.

Test cut done with Amazon boxes!

I designed the frame in Fusion360. It was built with 3 different materials and thicknesses: plexiglass, MDF, and supportboard for the back. This is my first multi-part laser piece.

Cutting like butter through the 1/4 MDF

These settings work for me for 1/4 dry MDF. 60watts, 10mm/s, 40-50% power, 2 passes (roughly 13 milliamps). It’s just enough to see the burn through the bottom and pop the pieces out of MDF.

Cut with the final materials

Pieces fit together perfectly. My laser hasn’t been calibrated yet so the cuts were slightly at an angle but for such small connections, it wasn’t an issue.

Added heart to the box, secured with hot glue gun

I added the piece to the frame. The light blue/white heart didn’t show to well with the white background.

Red really made the piece stand out

And here is the final product! Might engrave something on the bottom right later just for fun, but for now it looks amazing.

Categories
Builds

Squeeze Bottle Rack

In order to save counter space, I designed a rack in Fusion 360 to cut out 1/4 inch MDF rack. The rack is designed to be mounted to the side of a cabinet, and use double sided mounting tape (along with some physics) to securely hold the bottles in place.

Here it is mounted, perfect fit, snug

Categories
Builds

Yi Home Window Mount

Yi Home cameras are inexpensive, but you can’t use them outdoors. I built this 2 piece window mount (with SVG sticker for those who have a Cricut). This project was an exercise using Fusion 360 and threads, as well as practicing assembling components which is much like assembling parts in SolidWorks.

The Tools

  • 3D printer
  • Cricut Maker
  • Fusion 360
  • Cricut Maker

The Materials

  • PLA filament
  • double sided mounting tape
  • vinyl adhesive
  • Yi Home Camera

The Design

In order for the Yi Home IR (night) lights to work, the camera must be completely touching the glass of the window you’re mounting it do. Since mounting tape comes in different thicknesses, I decided to make this 2 pieces with threads so that the depth could be adjusted.

Mount the base to a clean window with your choice of double sided mounting tape, insert the camera into the other piece, screw in the camera until you feel it press up against the glass. If you leave a gap, you will see the reflection of the infrared lights.

Final printed product

Here is the final 2 piece product mounted to the window. It works great! The threads are really tight, and had to do some light sanding and screw and unscrew many many times to wear down the edge a bit.